The S&L Catalog
Pro AV Catalog
Manufacturers
PRODUCT CATEGORIES
Matching Keywords
Model Numbers
Request Quote
All Products
35watt Remote Mixer Amplifier, 4 Ohm / 8 Ohm, with Power Supply
Series:
Model: HD-RA35U
- Input 1 is switch-selectable MIC or LINE. Phantom voltage (IEC standard 24 Vdc) is switch-selectable for the microphone input. The line input is transformer isolated and accepts balanced or unbalanced, high or low impedance audio sources. A gain trimmer is
- A paging source is normally connected to Input 1. This input is equipped with push-to-talk terminals and with an adjustable threshold VOX circuit with LED threshold indicator, either (or both) of which may be set to duck ("fade down" or "mute") inputs 2, 3
- Input 2 is switch-selectable MIC or LINE. Phantom voltage (IEC standard 24 Vdc) is switch-selectable for the microphone input. The line input is active balanced and accepts balanced or unbalanced, high or low impedance sources. A gain trimmer is provided t
- An RDL Dual-LED VU meter is provided on the rear panel to indicate proper gain adjustment for Inputs 1 and 2. Correct input gain adjustment insures adequate mixer stage headroom.
- Inputs 3 and 4 each provide unbalanced stereo RCA input jacks, summed to mono.
Product Info
Tech Specs
Related Products
Documents
Accessories
The HD-RA35U is a four input audio mixer amplifier for systems demanding the broadest range of features and the highest energy efficiency. Two output power amplifier zones, 35 watts (Zone 1) and 4 watts (Zone 2), are driven from high-efficiency Class D amplifier stages. The mixer and amplifier sections all normally shut down (standby "sleep" mode) when audio is absent and automatically turn on when needed. A paging source is normally connected to Input 1. The Zone 1 amplifier output level for inputs 2, 3 and 4 is VCA controlled using various optional RDL remote controls. This allows the user controls to be conveniently wall mounted without running audio to and from the remote control location. The Zone 1 output drives 4 ohm or 8 ohm speakers. The output impedance is switch-selectable on the rear panel. The Zone 2 amplifier output drives an 8 ohm speaker and/or 600 ohm telephone equipment. The HD-RA35U is engineered, tested and manufactured in the U.S.A. to strict energy conservation standards. The unit consumes less than 1W of mains power in standby mode, and meets power amplifier efficiency specifications with analog-filtered Class-D digital output stages for both power amplifier output zones and for the 600 ohm output. The HD-RA35U features two mixers. The Zone 1 mixer is split between the front-panel (Paging Input 1 and tone controls) and a remote control (Inputs 2, 3 and 4) providing user level controls for the 35 watt amplifier output. The tone controls adjust the equalization at the Zone 1 amplifier output and can be switch selected on the rear panel to also adjust the equalization at the line-level output. The Zone 2 mixer on the rear panel provides level trimmers normally set by the installer to provide music-on-hold and/or for background music in a small zone equipped with an 8 ohm speaker. The Zone 2 section includes a 4 watt amplifier, a 600 ohm transformer-balanced MOH output, and an active balanced line-level output that may be used to feed another audio power amplifier. The HD-RA35U has four inputs that are common to both mixers. Inputs 1 and 2 accept balanced mic or line level sources. Inputs 3 and 4 accept unbalanced mono or stereo line-level sources.
- Input 1 is switch-selectable MIC or LINE. Phantom voltage (IEC standard 24 Vdc) is switch-selectable for the microphone input. The line input is transformer isolated and accepts balanced or unbalanced, high or low impedance audio sources. A gain trimmer is
- A paging source is normally connected to Input 1. This input is equipped with push-to-talk terminals and with an adjustable threshold VOX circuit with LED threshold indicator, either (or both) of which may be set to duck ("fade down" or "mute") inputs 2, 3
- Input 2 is switch-selectable MIC or LINE. Phantom voltage (IEC standard 24 Vdc) is switch-selectable for the microphone input. The line input is active balanced and accepts balanced or unbalanced, high or low impedance sources. A gain trimmer is provided t
- An RDL Dual-LED VU meter is provided on the rear panel to indicate proper gain adjustment for Inputs 1 and 2. Correct input gain adjustment insures adequate mixer stage headroom.
- Inputs 3 and 4 each provide unbalanced stereo RCA input jacks, summed to mono.
- Amplifier Signal Type - Audio
- Amplifier Type - Power Amplifier
- Spec Sheet available - Yes
- Amplifier Zones (2):: Zone 1 (Main): 35 W RMS, remote-controlled mixer (3 user controls) with paging input level control on front panel; Zone 2: 4 W RMS (8 Ohms), rear-panel mixer (trimmers)
- Audio Inputs (5):: 2, balanced, mic or line switch selectable on terminal blocks; 2, unbalanced stereo summing inputs on RCA jacks; 1, unbalanced amp in on RCA jack
- Gain Adjustments (2):: Inputs 1 and 2: Rear-panel single-turn trimmer
- Maximum Input Level:: Mic Inputs: -9 dBu; Balanced line inputs: + 20 dBu; Unbalanced Inputs: + 5 dBV (+11 dBV, one input); (for 1% THD+N at output)
- Phantom Voltage:: 24 Vdc (IEC 1938: 1996-12), switch-selectable for each mic input
- Ducking/Muting Actuation:: Automatic (Input 1 VOX: rear-panel adjustable signal threshold with LED indicator) or Manual (contact closure to ground)
- Ducking/Muting Release Delay:: Rear-panel single-turn trimmer, adjustable 2 to 6 seconds
- Ducking/Muting:: Switch-selectable for inputs 2, 3 and/or 4, 25 dB ducking attenuation, nominal
- Effects Loop:: Unbalanced RCA jacks (preamp output from main mixer, input to power amplifier)
- External RDL Module Power Output:: 24 Vdc, 100 mA maximum, ground-referenced
- Input level (to cross compressor threshold equaling 23 W amplified output):: Mic Inputs: -50 dBu (2.5 mV), (front panel and rear trimmer at max.) Balanced line inputs: -21 dBu (70 mV), (front pane Unbalanced Inputs: -15 dBV (180 mV), (front panel and rear trimmer at max., both inputs driven)
- Noise (line or amplified outputs):: Mic or Balanced line inputs: -70 dB (below compressor threshold at max gain); Unbalanced Inputs: <-75 dB (max gain)
- THD+N:: < 0.5% (1 kHz at compressor threshold, main amp output); < 0.1% (line output, main)
- CMRR:: Mic inputs: > 50 dB (50 Hz to 120 Hz); Balanced line inputs: > 80 dB (50 Hz to 120 Hz, transformer-coupled input)
- Compressor:: Threshold 2 dB below rated output, automatically adjusting attack and release times
- Frequency Response (mixer):: Mic to line output: ±1.5 dB (40 Hz to 25 kHz); Balanced line input to line output: ±1 dB (20 Hz to 20 kHz); Unbalanced line input to line output: ± 0.5 dB (20 Hz to 20 kHz)
- Frequency Response (amplifiers):: ±1 dB (50 Hz to 20 kHz)
- Tone Controls:: ±10 dB @ 10 kHz, ±9 dB @ 100 Hz (front-panel) with center detent
- Audio Outputs (2):: -10 dBV nominal (316 mV), dual mono unbalanced RCA (main mixer; FLAT or EQUALIZED, switch-selectable on rear panel); 0 dBu nominal balanced, terminal block (zone 2 mixer)
- MOH Output:: 0 dBu nominal (775 mV), 600 Ohm transformer-isolated, 16 dB headroom
- Power Amplifier Outputs (2):: Zone 1 (main, <1% THD+N): 35 W RMS (4 Ohms), 32 W (8 Ohms) on detachable terminal block (switch-selectable 4 or 8 Ohm impedance); Zone 2: 4 W (8 Ohms, on detachable terminal block)
- Indicators (9):: Front-panel: Signal present (4; 1 per input, green), Compressor activity (red), Power (bright=on, dim=standby, blue); Rear-panel: dual-LED VU meter (for inputs 1 and 2, green/red), Ducking/muting threshold (yellow)
- VCA (3):: Zone 1 (main) inputs 2, 3 and 4, 0 to 10 Vdc control, RJ45 (compatible with RDL VCA wall controls)
- Front-panel controls (4):: Zone 1 (main) paging level control (input 1), EQ (2, bass and treble), Power (momentary pushbutton, toggle on/standby)
- Rear-panel controls (22):: Gain trimmers (2, input 1 and 2), Mic/Line switch (2, input 1 and 2), Zone 1 line output pre/post-EQ switch, Effects loop bypass switch, Sleep (standby) mode delay (4 binary switches), Input 1 ducking/muting detector sensitivity trimmer, Phantom voltage switches (2, input 1 and 2), Ducking control switches (3, to duck inputs 2, 3, and/or 4), Tone control paging bypass (includes or excludes input 1 from tone controls), Zone 2 mixer level controls (4, inputs 1 through 4)
- Efficiency Standard:: "Energy Star® Program Requirements for Audio/Video" Version 2.0, applicable for passive remote control models (without muting)
- Sleep Mode Power Consumption:: < 1 W (amplifier and included power supply)
- Sleep Mode Delay:: 10 minutes to 2 hours (switch-selectable in 10 minute increments)
- Sleep Mode Disable:: Selectable
- Active Mode Delay:: 2 seconds (nominal) after input audio detected
- Audio Detector Threshold:: -80 dBu mic (at max input gain), -55 dBu balanced line (at max input gain), -42 dBV unbalanced
- Power Supply (included):: 100 to 240 Vac, 50-60 Hz, 50 W; 24 Vdc output to amplifier chassis
- Operating Temperature (Maximum): 122 F
- Operating Temperature (Minimum): 32 F
- Depth: 10 in
- Height: 3.50 in
- Width: 8.50 in
- Product Weight: 5.60 lbs
- Shipping Weight: 5.60 lbs
FP-NML2
- Network to Mic/Line Interface
FP-NML2P
- Network to Mic/Line Interface with PoE
FP-NML2VP
- Network to Mic/Line Interface with VCA, PoE
HD-MA35
- 35watt Mixer Amplifier with Power Supply - Low Impedance Output 4 Ohm or 8 Ohm
HD-MA35A
- 35watt Mixer Amplifier with Power Supply, Constant Voltage Output 25 V, 70 V or 100 V
HD-MA35AX
- 35W Mixer Amplifier, 25V or 70V or 100V Output, 4s Muting Release Delay
HD-MA35U
- 35watt Mixer Amplifier, 4 Ohm / 8 Ohm, with Power Supply
HD-MA35UA
- 35watt Mixer Amplifier, 25, 70, 100 V, with Power Supply
HD-PA35
- 35watt Power Amplifier with Power Supply, Low Impedance Output 4 Ohm or 8 Ohm
HD-PA35A
- HD-PA35A 35 Watt Power Amplifier with Power Supply - Constant Voltage Output 25 V, 70 V or 100 V
HD-PA35U
- 35 Watt Power Amplifier, 4 Ohm / 8 Ohm, with Power Supply
HD-PA35UA
- 35watt Power Amplifier; 25, 70, 100 V, with Power Supply
HD-PA35UX
- 35W Power Amplifier, 4ohms or 8ohms Output, 5dBV Maximum Input Level
HD-RA35UA
- 35watt Remote Mixer Amplifier; 25, 70, 100 V, with Power Supply
HD-RA35U 35 Watt Remote Mixer Amplifier - 4 Ohm / 8 Ohm, with Power Supply
3071 kb
- Data Sheet
HD-RA35U 35 Watt Remote Mixer Amplifier - 4 Ohm / 8 Ohm, with Power Supply
573 kb
- Instructions
Request Quote
Suggested Products
by
Crestron Electronics, Inc.
by
Crestron Electronics, Inc.
by
Crestron Electronics, Inc.
Thank you!
Someone will be in touch with you shortly.
Contact S&L Integrated
close
S&L Integrated
7 Midway Road
Thomasville, GA 31757
USA
(229) 378-8866
https://slintegrated.com/
Contact in regards to this product:
Radio Design Labs
Model: HD-RA35U
B2B INQUIRIES ONLY
Request more information from a dealer near you
close
Request more information from a dealer near you