The S&L Catalog
Zum® Wireless Universal Dimmer Module, 16A, 100-277V
Model: ZUMMESH-EXP-16A-DIMU
Part #: 6509686
- Pair and play wireless integration with Zum keypads, occupancy sensors, vacancy sensors, and daylight sensors
- Zum Mesh peer-to-peer RF communications for easy integration into a complete standalone or networked Zum wireless lighting control solution
- Single-channel universal lighting dimmer
- Supports dimmable LED, incandescent, electronic low-voltage, magnetic low-voltage, neon/cold cathode, and 2-wire fluorescent lighting loads
- Auto load-type detection
The Z?m™ Wireless ZUMMESH-EXP-16A-DIMU is a single-channel universal dimmer module designed to control a wide range of dimmable lighting load types. Utilizing proprietary zero-cross filter technology, the ZUMMESH-EXP-16A-DIMU compensates for line voltage and frequency fluctuations, providing superior immunity to power line noise and a dramatic reduction in lamp flicker.
Zum Mesh wireless technology affords easy "pair and play" integration as part of a complete Zum commercial lighting system. Energy-saving options are available to enable daylighting, occupancy or vacancy sensing, HVAC system integration, and centralized monitoring and management.
Auto-Detecting Universal Dimming:
Under normal operation, the ZUMMESH-EXP-16A-DIMU detects the connected load type and selects the appropriate operating mode automatically. Reverse phase (trailing edge) mode supports incandescent and electronic low-voltage load types, while forward phase (leading edge) mode supports LED, magnetic low-voltage, neon/cold-cathode, and 2-wire fluorescent load types. Center phase mode is also available, combining reverse and forward phase load control to address special cases. The operative mode is indicated by two LEDs located on the front panel.
Energy Efficiency:
Occupancy sensor, vacancy sensor, and daylight sensor connectivity drive the potential for significant energy savings.[1] Lights will turn off automatically when the room is vacant and dim gradually according the amount of natural daylight in the room. This reduces energy usage while maintaining a consistent light level for a comfortable workspace.
Pair and Play Setup:
Designed with flexibility and ease-of-use in mind, the ZUMMESH-EXP-16A-DIMU is pre-programmed with "pair and play" functionality. An installer can simply install the ZUMMESH-EXP-16A-DIMU along with Zum keypads, occupancy or vacancy sensors, and/or a daylight sensor, set up the room with a few quick button taps, and instantly control the lights in the room – no programming required! Room setup can also be accomplished using the Zum app if the room is equipped with a Zum Network Bridge.
Zum Mesh Wireless Technology:
Ultra-reliable Zum Mesh wireless technology provides steadfast peer-to-peer RF communications within a commercial space without the need for physical control wiring, hubs, or gateways. Employing a 2.4 GHz peer-to-peer mesh network topology, nearly every Zum Mesh device acts as a "routing node," relaying wireless commands directly between Zum Mesh devices to ensure that every command reaches its intended destination without disruption.
- Pair and play wireless integration with Zum keypads, occupancy sensors, vacancy sensors, and daylight sensors
- Zum Mesh peer-to-peer RF communications for easy integration into a complete standalone or networked Zum wireless lighting control solution
- Single-channel universal lighting dimmer
- Supports dimmable LED, incandescent, electronic low-voltage, magnetic low-voltage, neon/cold cathode, and 2-wire fluorescent lighting loads
- Auto load-type detection
- Forward and reverse phase dimming modes
- Zero-cross filter technology for reduced lamp flicker
- Extreme stability under noisy power line conditions
- Built-in air gap relay
- Mounts on a wall panel or above a suspended ceiling
- Surface mountable NEMA Type 1 enclosure
- UL® 2043 listed for installation in an environmental air handling space
- Meets UL 508 standard for industrial control equipment
- Meets CEC Title 24 energy efficiency standards
- Meets ASHRAE® 90.1 energy efficiency standards
- ICC® International Energy Conservation Code® compliant
- Spec Sheet available - Yes
- Operating Temperature (Maximum): 104 F
- Operating Temperature (Minimum): 32 F
- Certifications: IC, FCC, UL
- Wireless: Yes
- AC Voltage (Maximum): 277 Volts
- AC Voltage (Minimum): 100 Volts
- Current Draw: 16 Amps
- Depth: 3.19 in
- Height: 8.82 in
- Width: 6.38 in
- Product Weight: 3.44 lbs
- Load Control:
•Dimmer Channels: 1
•Dimmable Load Types: Incandescent, LED, electronic low-voltage, magnetic low-voltage, neon/cold cathode, 2-wire fluorescent - Wireless Communications:
•RF Transceiver: Zum Mesh 2-way RF, 2.4 GHz ISM Channels 15, 20, 25, or 26 (channel auto-selected), IEEE 802.15.4 compliant, AES-128 encryption
•Range (Typical): 50ft (15m) to nearest peer-to-peer mesh network device(s), subject to site-specific conditions and individual device capabilities - Controls and Indicators:
•TEST: (1) Pushbutton and (1) green LED, press and release the button to toggle the load output on and off, press and hold to cycle the dimming level up and down, LED indicates the load output is energized, also used for room setup and factory reset
•SETUP: (1) Pushbutton and (1) red LED, used for room setup and factory reset
•DIM MODE: (1) Pushbutton (behind cover), press to cycle through dimming modes: auto detect (default), reverse phase, forward phase, or center phase
•AUTO: (1) Red LED, indicates auto load type detection and phase mode selection is enabled
•REV: (1) Red LED, indicates reverse phase mode is enabled (automatically or manually)
•FWD: (1) Red LED, indicates forward phase mode is enabled (automatically or manually)
•CENTER: (1) Red LED, indicates center phase mode is enabled (automatically or manually)
•ZEROCROSS FILTER: (1) Pushbutton (behind cover), press to enable/disable zero-cross detection filter
•BASIC: (1) Green LED (behind cover), indicates basic zero-cross detection mode (default)
•FILTER: (1) Green LED (behind cover), indicates filtered zero-cross detection mode
•RESET: (1) Pushbutton (behind cover), initiates hardware reset
•NET: (1) Amber LED, indicates Zum Mesh network connection status and signal communications
•ERROR: (1) Red LED, indicates a variety of error conditions via blinking patterns (refer to the installation guide)
•POWER: (1) Green LED (behind cover), indicates line power is applied to either LINE terminal - Connections:
•Antenna: (1) Connection for supplied antenna
•NEUT: (3) Captive screw terminals; Neutral connections for feed and load; 24 to 10 AWG (0.25 to 4.0 mm2) wire size
•LINE: (2) Captive screw terminals; Line power feed input and pass-through; 24 to 10 AWG (0.25 to 4.0 mm2) wire size
•LOAD: (1) Captive screw terminal; Dimmed load output; 24 to 10 AWG (0.25 to 4.0 mm2) wire size Ground: (1) 3-terminal grounding block - Environmental:
•Humidity: 10% to 90% RH (non-condensing) - Construction:
•Enclosure: NEMA Type 1, galvanized steel with gray matte powder coated removable front cover panel, extruded aluminum heat sink on rear, (2) integral mounting flanges, (4) 1/2” or 3/4” conduit knockouts on bottom and lower left and right sides
•Mounting: Surface mount, must be oriented upright and mounted to a vertical surface with 6 inches (153mm) minimum spacing above and below for proper ventilation and heat dissipation
S&L Integrated
7 Midway Road
Thomasville, GA 31757
USA
(229) 378-8866
https://slintegrated.com/