The S&L Catalog
8-Channel Power Amplifier, 75W/Ch., 4/8 Ohm or 100V, International, 220-240V
Series: AMP-8000
Model: AMPI-8075
Part #: 6507874
- High-efficiency eight-channel amplifier
- Robust and reliable performance
- Professional sound quality
- 75W per channel at 4/8 Ohms
- Each channel configurable for Lo-Z or Hi-Z operation
Crestron® AMP-8000 series amplifiers are designed to complement the Crestron Avia™ family of digital signal processors, and are well-suited for all types of commercial audio applications. Each model furnishes eight channels of clean, efficient amplification in a space-saving 1 RU rack-mountable chassis. Each channel is configurable for Lo-Z or Hi-Z operation, as well as stereo and bridged modes. Network connectivity enables configuration, monitoring, and control via the Crestron Avia Audio Tool software, a Crestron control system, or Crestron Fusion®.
Solid and Efficient Performance
AMP-8000 series amplifiers are engineered to deliver exceptional performance and reliability with low distortion, low noise, and high power headroom. Advanced Class D technology maximizes efficiency to reduce power consumption and heat dissipation. An internal universal power supply with power factor correction ensures consistent performance with varying line voltages.
Configurable and Controllable
The AMP-8150 model delivers 150 watts per channel into 4 or 8 ohm “Lo-Z” loads. Each channel is individually configurable via software for use with “Hi-Z” distributed speaker systems (either 70V or 100V depending on model). Adjacent pairs of channels may be configured for stereo or bridged operation. Stereo mode enables remote control of a stereo pair of speakers using a single set of controls. Bridged mode allows two channels to be combined to provide a single channel delivering 300 watts into 8 ohms.
Two versions of the AMP-8150 are offered. The namesake AMP-8150 model supports 4/8 ohm and 70V output, and operates on 100-120V AC line power. The “international” AMPI-8150 model supports 4/8 ohm and 100V output, and operates on 220-240V AC line power.
Both models feature professionally balanced inputs and support input signal levels up to +24 dBu. Rear panel input attenuation controls allow for signal level matching. Remote level control and monitoring is enabled using the Crestron Avia Audio Tool software, or using a touch screen control panel or mobile device through integration with a Crestron control system. Integration with a control system also enables centralized monitoring and control of multiple amplifiers throughout a facility as part of a Crestron Fusion-managed enterprise.
Fully Protected
AMP-8000 series amplifiers feature comprehensive protection against overheating, shorted or overloaded speaker lines, excessive signal levels, and other faults. Each channel is independently protected, allowing an individual channel to enter protection mode without interrupting the operation of other channels. Protection is automatic, quickly disconnecting the speaker line and shutting down the affected channel, and then restoring normal operation once the fault is resolved. Clear indication of any fault is provided on the front panel, and may also be reported to a control system to provide notification on a touch screen or mobile device, through a text message or e-mail, or at a central help desk using Crestron Fusion.
- High-efficiency eight-channel amplifier
- Robust and reliable performance
- Professional sound quality
- 75W per channel at 4/8 Ohms
- Each channel configurable for Lo-Z or Hi-Z operation
- Model AMPI-8075 supports 220-240VAC line power and 4/8-ohm or 100V output
- Mono, stereo, and bridged modes
- Comprehensive fault and speaker protection per channel
- Extensive front panel status indicators and output meters
- High-speed Ethernet LAN connectivity
- Software configuration, control, and monitoring
- Crestron® control system integration support
- Crestron Fusion® Cloud enterprise management support
- Rear panel +24 dBu balanced inputs and level adjustments
- Detachable terminal block connectors for easy servicing
- Single-space 19-inch rack mountable
- High-density stackable without extra vent spacing
- Amplifier Type - Power Amplifier
- Rackmountable - Yes
- Spec Sheet available - Yes
- Impedance: 8 ohm
- Number of Channels: 8
- Number of Watts Per Channel: 75 Watt
- Rack Units (Height): 1
- AC Voltage (Maximum): 240 Volts
- AC Voltage (Minimum): 100 Volts
- Operating Temperature (Maximum): 104 F
- Operating Temperature (Minimum): 41 F
- Certifications: UL, FCC
- Total Harmonic Distortion + Noise (THD+N): 0.10 %
- Active Power: 173 Watt
- Depth: 14.69 in
- Height: 1.72 in
- Width: 17.28 in
- Product Weight: 12.60 lbs
- COMMUNICATIONS:
•Ethernet: 10/100Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, TCP/IP, UDP/IP, CIP, DHCP, SSL, SSH, SFTP (SSH File Transfer Protocol)
•USB Device: USB device port for computer console (setup) - Audio:
•Input Signal Types: Balanced or unbalanced analog line level
•Output Signal Types: 4/8 Ohm, 70 Volt direct-coupled (AMP-8075 only), 100 Volt direct-coupled (AMPI-8075 only)
•Operating Modes: (Configurable via Avia Audio Tool software)
•Mono: Each channel is configurable to operate independently from all other channels
•Stereo: Adjacent channels (1 and 2, 3 and 4, 5 and 6, 7 and 8) are configurable to operate as a stereo pair with linked control settings
•Bridged: Adjacent channels (1 and 2, 3 and 4, 5 and 6, 7 and 8) are configurable to operate as an 8 Ohm bridged mono output
•4/8-ohm Mode: Each channel is configurable for 4/8 Ohm “Lo-Z” output
•70V Mode (AMP-8075 only): Each channel is configurable for 70 Volt “Hi-Z” output
•100V Mode (AMPI-8075 only): Each channel is configurable for 100 Volt “Hi-Z” output
•Output Power, AMP-8075: 75 Watts per channel at 4-8 Ohms or 70 Volts nominal
•150 Watts per bridged pair of channels at 8 Ohms
•Output Power, AMPI-8075: 75 Watts per channel at 4-8 Ohms or 100 Volts nominal
•150 Watts per bridged pair of channels at 8 Ohms
•Frequency Response: 20 Hz to 20 kHz +/-0.5 dB at 1 Watt, 4-8 Ohms
•200 Hz to 20 kHz +/-0.5 dB at 1 Watt, 70/100 Volts
•High Pass Filter: -3 dB at 80 Hz, 12 dB per octave in 70V or 100V mode
•THD+N: <0.1% at 1 kHz at 3 dB below clipping
•S/N Ratio: >103dBA, 20Hz to 20kHz
•Channel Separation: >70dB
•Input Sensitivity: 1.23 Vrms, +4 dBu (balanced) for full rated output power
•Fault Protection:
•Over Current: Protects each channel individually against an excessive speaker load or shorted speaker line
•DC Offset: Protects each channel and speaker line against DC voltages sensed at each output
•Over Temperature: Protects the amplifier power supply and each channel against overheating due to poor ventilation or excessive temperature
•Under Voltage: Protects the amplifier if the internal power supply voltage is below tolerance due to excessive output levels or insufficient line voltage
•Note: All faults report to the control system, and indicate on the front panel and in the software tool.
•Output Relays: Disconnects the speaker line at each output under fault conditions, and during startup and shutdown
•Audio Ramp: Ramps each channel’s audio level up to its last used setting after the corresponding output relay has closed following startup or fault recovery; ramp time ~2 seconds - Connectors:
•LINE INPUTS 1 - 8: (8) 3-pin 3.5 mm detachable terminal blocks
•Balanced line-level audio inputs
•Maximum Input Level: 12.3Vrms, +24dBu
•Input Impedance: 20k Ohms balanced
•SPEAKER OUTPUTS 1 - 8: (8) 2-pin 7.62 mm reversed gender 20A detachable terminal blocks
•Power amplifier outputs
•Wire Size: Terminals accept up to 12 AWG (3.31 mm2)
•Note: Output is direct-coupled in all modes for all load types, not transformer isolated
•LAN: (1) 8-pin RJ45 female
•10Base-T/100Base-TX Ethernet LAN port
•100-120V~ 50/60Hz 3A (AMP-8075): (1) IEC 60320 C14 main power inlet
•Mates with removable power cord (included)
•220-240V~ 50/60Hz 2A (AMPI-8075): (1) IEC 60320 C14 main power inlet
•Mates with removable power cord (included)
•FUSE: T10AH250V (AMP-8075): Main fuse
•1/4 x 1-1/4-inch, 10A, time-lag, 250V, ceramic
•FUSE: T6AH250V (AMPI-8075): Main fuse
•5 x 20 mm, 6.3A, time-lag, 250V, ceramic
•G: (1) 6-32 screw
•Chassis ground lug
•COMPUTER (front): (1) USB Type B female
•USB computer console port (for setup only) - Controls and Indicators:
•PWR: (1) Bi-color green/amber LED, indicates operating power supplied from AC line power, amber indicates startup in progress, green indicates normal operation, alternating green/amber indicates absence of a network connection
•RESET: (1) Recessed pushbutton, restores last saved settings
•STATUS, FAULT 1 - 8: (8) Red LEDs, each indicates an under-voltage fault condition on the corresponding channel
•STATUS, CURRENT 1 - 8: (8) Blue LEDs, each indicates an over-current fault condition on the corresponding output
•STATUS, DC 1 - 8: (8) Blue LEDs, each indicates a DC offset fault condition on the corresponding channel
•STATUS, THERM 1 - 8: (8) Blue LEDs, each indicates an over-temperature fault condition on the corresponding channel
•STATUS, 70V 1 - 8 (AMP-8075 only): (8) Blue LEDs, each indicates the corresponding channel is configured for 70 Volt operation
•STATUS, 100V 1 - 8 (AMPI-8075 only): (8) Blue LEDs, each indicates the corresponding channel is configured for 100 Volt operation
•VU 1 - 8: (8) 5-segment LED bar graph audio level meters for each corresponding output; each contains (4) blue LEDs for -40dB, -30dB, -20dB, and -10dB, and (1) red LED for CLIP
•LINE INPUTS 1 - 8 (rear): (8) Screwdriver-adjustable rotary controls, each adjusts the input at tenuation level for the corresponding channel
•LAN (rear): (2) LEDs, green LED indicates Ethernet link status, amber LED indicates Ethernet activity
•SETUP (rear): (1) Red LED and (1) pushbutton for Ethernet setup, flashes while updating firmware
•Power Switch (rear): (1) Rocker switch, turns main power on or off - Construction:
•Chassis: Metal, variable-speed fan-cooled, vented sides
•Front Panel: Metal, black finish with polycarbonate label overlay
•Mounting: Freestanding or 1 RU 19-inch rack-mountable (front rack ears and rear support brackets included) - Environmental:
•Humidity: 10% to 90% RH (non-condensing)
•Heat Dissipation: 350BTU/hr, all channels driven at 1/8th output power; 250BTU/hr, all channels idle
S&L Integrated
7 Midway Road
Thomasville, GA 31757
USA
(229) 378-8866
https://slintegrated.com/