X-Series Amplifier, 75 W

Model: AMP-X75

Compact, configurable ENERGY STAR® certified power amplifier
Quarter-rack width form factor, gangable with other next generation half- and quarter-rack width form factor Crestron products
1 RU high design is surface or rack mountable
Configurable for either LoZ or Hi-Z operation
Configurable for 1 x up to 75 W output for Hi-Z or

More Product Information Below

Compare

Project List

Product Info

Tech Specs

Documents

The Crestron® AMP-X75 is a high performance, space saving, energy efficient amplifier that' totally configurable, yet simple to use. Whether you need a stereo amplifier that mounts on a wall or under a table, or a high impedance speaker run fed from a rack mounted unit, the AMP-X75 is simple to specify and install in any configuration.

LoZ (4/8 ohms) and Hi-Z (70V or 100V) Output

The AMP-X75 is a 2-channel amplifier (up to 35 W per single-ended, low impedance channel) which can also be configured for a single channel of bridged operation (up to 75 W for the bridged channel), or for a single channel of high impedance operation (up to 75 W) to drive a distributed speaker system (70V or 100V). Balanced and unbalanced inputs are available for connection to a single stereo or two mono source(s) via detachable terminal blocks or a 3.5 mm TRS connector. Balanced and unbalanced inputs are summed for simultaneous use.

Solid and Efficient Performance

The AMP-X75 is engineered to deliver exceptional performance and reliability with low distortion, low noise, and high power headroom. Advanced Class D technology maximizes efficiency to reduce power consumption and heat dissipation. An internal universal power supply ensures consistent performance at varying line voltages.

Convection Cooling

The efficient design ensures cool running operation and long-term reliability. The AMP-X75 is high-density stackable with other Crestron modular amplifiers, allowing multiple units to be installed vertically in an equipment rack without needing extra ventilation space.

Compact, configurable ENERGY STAR® certified power amplifier
Quarter-rack width form factor, gangable with other next generation half- and quarter-rack width form factor Crestron products
1 RU high design is surface or rack mountable
Configurable for either LoZ or Hi-Z operation
Configurable for 1 x up to 75 W output for Hi-Z or
Bridged or 2 x up to 35 W output for stereo low impedance
Low noise, low distortion, and high headroom
Comprehensive fault and speaker protection
Captive speaker connectors for secure and robust connectivity
Support for two channels of balanced or unbalanced line inputs
Stereo or mono-summed operation
Convection cooled for noiseless operation
Standby functionality turns on amplifier in approximately 0.1 s when input sensing circuitry detects an audio signal
Rack and surface mount parts are included
Stereo ALS line level output for assistive listening systems
Remote standby feature allows for instant on/off control over amplifier outputs via a simple contact closure input
Front panel power/standby, Hi-Z, fault, and signal/clip indicators
Internal universal 100-240V power supply

Amplifier Type - Power Amplifier
Energy Star rated - Yes
Rackmountable - Yes
Warranty - Yes
Spec Sheet available - Yes

Operating Temperature (Maximum): 104 F
Operating Temperature (Minimum): 41 F
AC Voltage (Maximum): 240 Volts
AC Voltage (Minimum): 100 Volts
Active Power: 18.63 Watt
Standby Power: 0.41 Watt
Depth: 8.78 in
Height: 1.83 in
Width: 4.33 in
Product Weight: 2.10 lbs
Regulatory Compliance: ErP, UL, FCC
Audio:
•Input Signal Type: Balanced or unbalanced analog line-level
•Frequency Response : 20 Hz to 20 kHz ±0.5 dB at 1 W
•High-Pass Filter (70V and 100V operation only): -3 dB at 80 Hz, -12 dB/octave
•THD+N: <0.1% at 1 kHz at -3 dB full rated output power
•S/N Ratio: >103 dBA, 20 Hz to 20 kHz, balanced
•Crosstalk: -75 dB at 1 kHz
•Input Sensitivity: 1.23 Vrms, +4 dBu balanced;0.316 Vrms, -10 dBV unbalanced; For 35 W (8 Ohms), 75 W (70V/100V)
•Gain: 23 dB at 8 Ohms, Balanced Input
•Protection: Clipping, over current, under voltage, over temperature, DC offset, extreme high frequency
•Standby Mode: 25 minutes with no signal present, typical
•Wake Time: 0.1 s typical
•Wake Threshold: 0.44 mV typical
Connectors:
•SPEAKER OUTPUT: (1) 4-pin 5.08 mm pitch, 12A plug with screw locking retainers; Power amplifier output; Wire Size: Terminals accept up to 12 AWG (3.31 mm2)
•AUDIO IN (UNBALANCED): (1) 3.5 mm TRS connector, female; Unbalanced line-level audio inputs;
•Maximum Input Level: 2.24 Vrms, +7 dBV (+9.2 dBu)
•AUDIO IN (BALANCED): (2) 3-pin 3.5 mm detachable terminal block; Balanced line-level audio inputs; Maximum Input Level: 7.75 Vrms,+20 dBu; Input Impedance: 20k Ohms
•ALS OUT: (1) 3.5 mm connector, female; Unbalanced line level audio output,0.316 Vrms, -10 dBV nominal; Maximum Output Level: 2.24 Vrms,+7 dBV (+9.2 dBu); Fixed audio output for assisted listening devices duplicates the summed (Unbalanced + Balanced) audio inputs
•REMOTE: (1) 2 pin 3.5 mm detachable terminal block; Connect to dry contact closure to place amplifier in standby mode.
•G: (1) 6-32 screw; Chassis ground lug
•100-240V~ 370-200 mA 50/60 Hz: (1) IEC 60320 C14 main power inlet; Mates with removable power cord, included
Controls and Indicators:
•PWR: (1) White/Red LED; White indicates amplifier is on and ready for use; Red indicates amplifier is in standby
•HI-Z: (1) White LED; Indicates when Hi-Z mode is enabled (70V or 100V); Channels 1 - 2 are bridged and set to 70V or 100V operation
•SIGNAL: (2) White/Red LEDs (one per input); White indicates when an active input signal is presentRed indicates when an active input signal clip/limiting is present
•FAULT: (2) Red LEDs (one per input); Indicates that the input channel is faulted
•GAIN 1-2: (2) Screwdriver-adjustable, detented rotary controls, one per input channel; Adjusts the input attenuation level for the corresponding amplifier channel
•Modes: (1) Slide switch; Selects stereo, summed, bridged, 70V, or 100V operation
•STEREO (LoZ): The input signal received on each channel is sent to its respective output for use in applications where left and right channel separation is required. The two GAIN controls are independently adjustable
•SUM (LoZ): The input signals sent to a channel pair (1 + 2) are summed and sent to their respective individual outputs. The two GAIN controls are independently adjustable
•BRIDGE (LoZ): The input signals sent to a channel pair (1 + 2) are summed and sent to a bridged output (1 + 2) for use in high-power applications. The GAIN 1 control adjusts the bridged 1 + 2 output
•70V (Hi-Z): The input signals sent to a channel pair (1 + 2) are summed and sent to a bridged output (1 + 2) for use in Hi-Z 70V applications. The GAIN 1 control adjusts the bridged1 + 2 output
•100V (Hi-Z): The input signals sent to a channel pair (1 + 2) are summed and sent to a bridged output (1 + 2) for use in Hi-Z 100V applications. The GAIN 1 control adjusts the bridged 1 + 2 output
Humidity: 10% to 90% RH (non-condensing)
Heat Dissipation: 63.6 BTU/hr at 4 Ohms, all channels driven at 1/8th output power; 25.9 BTU/hr, idle (Hi-Z mode); 1.4 BTU/hr in standby
Construction:
•Chassis: Metal, convection cooled (fan less)
•Front Panel: Metal, black finish with polycarbonate label overlay
•Mounting: Freestanding, surface mount, or 1/4 width 1 RU 19 in. rack mountable;Gangable with other Crestron modular AMP series products (adhesive feet, surface mounting, rack mounting, and ganging hardware all included)

Amplifier 2509232 kb - Data Sheet

Project List

The S&L Catalog

X-Series Amplifier, 75 W

Model: AMP-X75

Company

Verticals

Contact Us

Education

Corporate

Government

Healthcare

Worship

Packages

Solutions